How Tight Skateboard Wheels

Something about a tight set of skateboard wheels just feels right. When you’re cruising around town or carving up a hill, there’s nothing like the feeling of a well-tuned set of wheels underneath you. In this article, we’ll look at how tight skateboard wheels are and how to tighten them up yourself. Let’s get started!

Skateboard wheels can loosen for a variety of reasons. A well-worn set of wheels will become looser as the bearings wear down and the wheel’s grip on the pavement decreases. Loose wheels can also be caused by environmental factors such as rain or snow, which can cause the bearings to rust and the wheel to slip. Finally, the incorrect assembly can also lead to loose wheels.

How Tight Skateboard Wheels

Required Materials

  • Skateboard
  • Allen wrench
  • Screwdriver
  • Pliers
  • Adjustable wrench

If your skateboard wheels are loose, you can tighten them up using a few basic tools. You’ll need an Allen wrench, screwdriver, pliers, and adjustable wrench. Let’s take a look at how to do it!

How Tight Skateboard Wheels Methods

Method 1: Fixing Loose Trucks

A loose-fitting truck can be fixed by tightening the kingpin nut to compress the bushings.

You can usually crank down on the nut for new skateboard trucks with no wear on them before it becomes noticeably more difficult to turn. For trucks that have been used and loosened up a bit, slowly increase how tight you make it until it is firm and will not quickly move when you shake the board.

Loose-fitting Truck Can Be Fixed

If your kingpin nut cannot be tightened anymore without increasing how difficult it is to turn, back off a quarter of a turn and test ride again. Repeat this process until you get barely more than enough resistance from the bushings to prevent movement of the wheels while riding you want some give).

Method 2: Fixing Wobbling Wheels

A stable wheelbase is required for good tight skateboard wheels. The longer the wheelbase, the more stable your ride will be. To check to see how you are doing in this department, stand over your board and place both feet parallel with the trucks facing forward on either side of the board’s centerline to tight skateboard wheels.

If your wheels are stable, you should be able to take your hands off of the board and not notice any wobble to tight skateboard wheels. However, if you find that one or both wheels are unstable, refer to the how tight skateboard trucks section for ways to reduce or fix this problem.

Method 3: Tightening Screws

Because how tight skateboard wheels are so important for the safety of your board, it’s essential to find out how tight skateboard wheels should be. If you’ve ever had one fly off when riding, you understand how much it can suck. I’m not saying this is always a bad thing because sometimes these things create new tricks! But if you’re skating in a crowded area or near cars, how tightly skateboard wheels should be could really save your life.

Tightening Skateboard Screws

Several methods work well, but there are also some risks involved with each technique, making them less desirable for certain situations. Keep in mind tight skateboard wheels should be is determined by loose or tight skateboard wheels are how tight skateboard trucks are, and how loose the how tightening skateboard wheel nuts are.

Method 4: Further Adjusting Your Trucks

Another method to tighten your skateboard wheels is to adjust how tightly your trucks are fastened. If you have already tried the first three methods but are still struggling with how tight skateboard wheels are, then it may be that your trucks are too loose.

Loose trucks will cause you to get wheel bite, often leading to breaking parts of your board and injury. In addition, the trucks allow you to turn, so you will lose control of how sharp or wide your turns are without them being tight enough. Here’s how to adjust the tightness of your trucks:

  1. Place the key into the truck one truck at a time by slipping it into the small hole underneath the truck.
  2. Angling the key upwards, get one end of it underneath the skateboard truck’s bolt head and give it a quarter turn in either direction until you feel or hear it click into place.
  3. Take your time when turning the key, so you do not strip out the screw head in the process. Keep applying pressure until the screw locks into place.
  4. Check how tight your trucks are by trying to wiggle the skateboard truck back and forth with pressure applied to it by your hand. If you cannot feel any movement, then it is likely that the trucks are now tight enough for you to control tight skateboard wheels are.
 Control Tight Skateboard Wheels

Truck Tightness In Different Scenarios

1. When Going Downhill

When going downhill, your board is under a lot of stress. The best scenario for tight skateboard wheels would be to tighten the nuts until there is no play in the truck when you shake it side to side and add a cushion if needed (more on how cushions work later).

2. When Doing Slides

When doing slides, the trucks should be very loose. If there is even a little bit of resistance when you try to slide your board, it’s too tight.

3. When Cruising Around Town or in the Park

When cruising around town or in the park/skatepark, the trucks should be somewhat loose so that they turn easily when you lean in one direction or another. You loosen the nuts enough so that when you do a hard turn, there is little resistance (but not too loose like how it is when doing slides).

You Can Check It Out to Speed Check on A Longboard

4. When Doing Tricks

For tight skateboard wheels are related to tricks, the trucks should be very loose. The less resistance you have when turning, the easier it will be for tricks like ollies and flips. That is because if the truck is too tight, you won’t get enough ollie power or flip power.

Skateboard Wheels Are Related to Tricks

When doing tricks in general, if you tighten the nuts all the way, it makes the board closer to tight skateboard wheels when going downhill. So if you are trying a trick and notice that there is a lot of resistance when turning, then you need to loosen your truck more.

5. For Cruising

When you are going down hills and doing tricks, tight skateboard wheels are a very important aspect of how your board rides. However, when cruising around town or the park, it matters how fast you get your board to turn from side to side. This has more to do with how loose your trucks are rather than how tight they are. The more loose your trucks are, the faster you can turn (especially when doing slides).

6. For Skate Ramp

Your board wheels should be a skater to the ground. Make sure wheels are touching the platform of the ramp while you’re riding this one out.

7. For Flipping

This is tight skateboard wheels are; then, you should be able to freely stand over your board and rotate your trucks without interference.

You Can Check It Out to Mark the Front of Your Skateboard

Frequently Asked Question

Which Kind of Wheel Is Best for You, Cheap or Expensive?

The answer to this question really depends on how you plan to use your skateboard. If you plan to do a lot of tricks and stunts, then you will need a set of wheels that is durable and can withstand a lot of wear and tear. This typically means that you will need to spend a little more money on your wheels. However, if you are just using your skateboard for cruising around town or at the skatepark, then you can get away with using a cheaper set of wheels.

Which Is Better: A Loose or Tight Skateboard Wheel?

There is no definitive answer as to which is better: a loose or tight skateboard wheel. It really depends on how you plan to use your skateboard and what type of terrain you will be riding on. If you are doing tricks and stunts, then you will need a set of wheels that is durable and can withstand a lot of wear and tear.

This typically means that you will need to spend a little more money on your wheels. However, if you are just using your skateboard for cruising around town or at the skatepark, then you can get away with using a cheaper set of wheels.

How Do You Adjust a Tight Skateboard Wheel?

If your skateboard wheels are too tight, you can loosen them by adjusting the nuts on the truck. You want to loosen the nuts enough so that there is little resistance when turning, but not too loose like how it is when doing slides.

How Long Should Skateboard Wheels Spin For?

How long skateboard wheels should spin for is based on how fast you want to go. If you are going downhill, you want the wheels to spin as fast as possible so that you can get down the hill as quickly as possible. On the other hand, if you are doing tricks, you want the wheels to spin more slowly so that you have more control over your board.

Conclusion

The right tightness is key. Of course, you’ll need to experiment with what’s best for your skating style, but this guide should help you get started! Thanks for reading our post about how tight skateboard wheels are.

You may also read: How Tight Should Longboard Wheels Be

Leave a Comment