How to Put Spacers on Skateboard

There are many things to consider when you are putting together a skateboard. One of the most important decisions you’ll need to make is what type of spacers to use. This article will discuss the different types of spacers and how to put spacers on skateboard. We’ll also provide tips for choosing the right spacer for your needs. In this article, we will teach you how to do it. Keep reading for more information.

There are many reasons why it’s important to put spacers on your skateboard. First of all, spacers help protect your bearings from dirt and debris. They also help keep your bearings lubricated, which can increase their lifespan. Spacers also help to improve the stability of your skateboard, and they can make it easier to turn. Finally, spacers can help prevent wheel bites, which can cause damage to your deck.

How to Put Spacers on Skateboard

Required Materials

To install spacers on your skateboard, you will need:

  • a skateboard
  • spacers of the appropriate size
  • a screwdriver or wrench

If you are using bolt-on spacers, you will also need:

  • a socket wrench
  • an Allen wrench

How to Put Spacers on Skateboard Step by Step Guide

Step 1: Read All of These Instructions!

The first thing you need to do before installing your spacers is read all of the instructions. We cannot stress this enough. Skateboard manufacturers are generally pretty serious about how to put spacers on skateboard, and they treat it as a kind of “do not try this at home” situation. This is because installation can be dangerous if you do not follow the proper steps.

To be safe, you should read all of the instructions that came with your spacers before you try to install them. Usually, there are a few different sets of instructions, and they will have some small details in common with each other.

Step 2: Prepare Your Spacers

Before you start anything, you should ensure that your spacers are clean enough to work on. If they are dirty or rusty, this can affect how well they hold on to the board.

Prepare Your Spacers for Installation

To prepare your spacers for installation, rinse them off with water and let them dry completely before proceeding. You should also check how the instructions tell you to install your spacers. For example, some will require you to use a screwdriver, while others might say that you should use a socket wrench. How your spacers are configured could make a big difference in how the installation is done.

Step 3: Install Your Spacers

Now it’s time to get busy installing your spacers! The first step is to find the bearing that you plan to install your spacers into. Once you have found it, remove the outermost shield of the bearing using either a screwdriver or wrench.

Now comes one of two very important steps. Some spacers require you to install them with their hexagonal opening facing outwards, while other spacers are designed to be installed into the bearing with their hexagonal opening facing inwards. This all has to do with how the spacer was manufactured, so look at your spacers carefully to see which orientation they require.

Once you have figured out how your spacers need to be oriented, please take one of them and slide it over the skateboard’s axle until it’s on top of the bearing. Next, flip your board over and spin it slowly while applying moderate tension to your spacers. This will allow you to set them so that they are perfectly straight and don’t wobble or rattle when you ride your board.

If this method is not working for you, check how your manufacturer says to install your spacers. For example, you might need to hold them in place with a tool while turning the skateboard over and spinning it. This is how most wrench-based installations are done, so switch up how you do it if this does not work for you or if that’s how it needs to be done.

Step 4: Replace Any Outer Spacers

Once you have your spacer in place, all left is to replace the bearing shields around it and tighten them down. Next, line up one side of the shield with how it was before, and repeat this process for the other three sides.

Replace the Bearing Spacers

If you are using bolt-on spacers, this will be much easier to do with a socket wrench. However, if you are using screw-in spacers, the process should not take too long, even with a regular screwdriver. First, apply some pressure and twist the screwdriver in small increments until each shield is firmly pressed down against your spacer.

Step 5: Test Your Work

Now that your spacers are installed, it’s time to see how well they work! Go ahead and ride your board around for a bit. If there is any wobbling or rattling from the spacers, you might need to go back and tighten them down again. Generally, this isn’t how to put spacers on skateboard are supposed to sound, so if that’s how it is, you might need to try a different installation method.

It can be hard to install your spacers if you don’t know how they were made or how they should work. Luckily, there is a fairly straightforward way to do this, and it always works. Once you have done it once, you should be able to do it again without the instructions. All that’s left is for you to enjoy how your board sounds and feels with spacers installed!

You Can Check It Out to Take Plastic Off Skateboard Wheel

Do I Need Bearing Spacers, and If so How Do I Install Them?

Most skateboard bearings do not have pre-installed spacers, so you will likely need to install them yourself. Depending on the type of spacer that you are using, the installation process may vary. If your spacers have a hexagonal opening, you will likely need to install them with the opening facing outwards. However, some spacers are designed to be installed with the opening facing inwards. Be sure to check how your spacers should be installed before proceeding with the installation process.

Installing the Spacer

The installation process usually involves installing the spacer over the skateboard’s axle and then flipping the board over and spinning it while applying tension to the spacer to set it in place. If this does not work for you, check how your manufacturer says to install your spacers. You might need to hold them in place with a tool while turning the skateboard over and spinning it. This is how most wrench-based installations are done, so switch up how you do it if this does not work for you or if that’s how it needs to be done.

Frequently Asked Question

How Can I Tell if My Board Is Warped or Crooked?

It might be warped if you’re having trouble keeping your board straight, or it seems to be wobbling more than it should. Put the board on a flat surface and measure the distance from one side to the other at the center. If it’s not the same on both sides, your board is warped, and you’ll need to fix it. A crooked board will also cause problems when trying to do tricks. If your board is just a bit off-kilter, you can try using spacers to correct the problem.

What Are Spacers and How Do I Put Them on My Skateboard?

Spacers are small plastic or metal washers that you can use to adjust the distance between the trucks and your skateboard deck. This will help keep your board straight and can be especially helpful if your board is warped. To put spacers on your skateboard, you’ll need to remove the screws that hold the trucks in place.

Place a spacer on each side of the truck, between the deck and the truck, then replace the screws. Make sure that the spacers are evenly spaced and that they don’t move around when you ride. If they start to move, tighten the screws a bit.

What Is the Best Way to Clean and Maintain My Skateboard Deck?

The best way to clean and maintain your skateboard deck is to use a damp cloth to wipe it down after each use. Be sure to dry the deck thoroughly, especially if it’s made of wood, to avoid warping. You can also use a light coat of wax once a month or so to help protect the deck and keep it looking new.

Clean and Maintain My Skateboard Deck

Can I Fix My Board Myself, or Should I Take It To A Professional?

If your board is warped, you will need to take it to a professional. However, you can try using spacers to correct the problem if it’s just a bit off-kilter. To put spacers on your skateboard, you’ll need to remove the screws that hold the trucks in place. Place a spacer on each side of the truck, between the deck and the truck, then replace the screws. Make sure that the spacers are evenly spaced and don’t move around when you ride. If they start to move, tighten the screws a bit.

Which Type of Spacers Work Best for Me?

There are a few different spacers available, so which type is best for you? Plastic spacers are the most common and are usually the cheapest. They’re also lightweight and easy to install. Metal spacers are a bit heavier but can be more durable. They’re also less likely to move around than plastic spacers. If you’re having trouble keeping your board straight, metal spacers may be better.

You Can Check It Out to Cruise on A Skateboard

Conclusion

So, there you have it! Your complete guide to putting spacers on your skateboard. We hope you found this tutorial helpful and that you are now sprucing up your skateboard with some new spacers. If you have any questions or comments, be sure to leave them in the comment section below. Thanks for reading our post about how to put spacers on skateboard.

You may also read: How to Know the Nose and Tail of a Skateboard

Leave a Comment